"Liner Transfer and Packaging System" takes advantage of the features of B&R's ACOPOStrak track-based technology and introduces a shuttle to grasp two types of packaging materials. This revolutionary packaging system can simultaneously perform the two packaging processes of "zipper pouch" and "carton" in one loop. It enables a variety of packaging proposals and realizes space and cost savings.

Product Features
The same shuttle can be used on one line and completely different packaging operations can be performed on the opposite side, saving space and cost.
Shuttles are imprinted with QR codes, which can be read by a bar code reader while running, allowing the distance traveled and operating status of each shuttle to be checked and managed on the operation panel.
In addition, shuttles running in a loop can be sent out from the side lane, allowing shuttles to be replaced without stopping operation during maintenance.

”Ultrasonic flowwrapper FUW3400/B alpha8” can contribute to the SDGs.
By evolving its "sealing technology" and incorporating an ultrasonic horn and anvil into a conventional horizontal flowwrapper, film welding has been achieved.

The sealing area does not heat up, so there is little thermal impact on the product or film.
The "ultrasonic heating seal" generates ultrasonic waves only at the moment of sealing, and seals the film using ultrasonic vibrations, so the sealing area does not heat up, making it effective for packaging lines that have a lot of standby time, and for packaging products that are sensitive to heat, such as chocolate and candy.

Product Features
Energy saving (35% power saving compared to conventional machines)
Compared to conventional heat sealing machines, it is possible to reduce power consumption by approximately 35% (compared to conventional heat sealing methods: 947wh → 618wh). There is also no need for warm-up power after turning on the power, which contributes to reducing packaging materials and CO2 emissions.

Improved product finish of the sealed part
By using line sealing, the product finish of the sealed part is improved. In addition, it is now possible to use films (single film/mono-material packaging materials) that were difficult to use with the heat sealing method, which also contributes to the SDGs.

Reducing the amount of film used by shortening the cutting pitch
By reducing the area of ​​the sealed area by using line sealing, it is possible to achieve a cutting pitch of -10 mm per bag. This shortens the end seal width and contributes to reducing packaging material costs.

Since there is no heat source, the risk of workers getting burned is reduced. Since there is no heat source like a heat sealer, the risk of workers getting burned during maintenance is reduced.

Fuji Smart Module” enables centralization of packaging processes
Fuji Smart Module” enables to unify the packaging process from individual wrapping to caser by integrating a Flowwrapper machine and other machines manufactured by other manufacturers into the frame of ‘Fuji Smart Module’.

Product Features
The use of frames of the same shape creates a sense of uniformity in the equipment.
Space and manpower saving by incorporating robots and packaging machines
Control panel is located on the top, which improves workability and cleanability during maintenance
Improved visibility and safety due to large transparent cover

Robotization of heavy labor required for stacking cardboard boxes by humans saves manpower and labor

Product Features
Capable of stacking two pallets
　After one pallet is stacked, the machine starts stacking the other pallet without stopping the line.
　It is also possible to stack cardboard boxes coming from two different lines on one pallet each.
Robot hand that meets safety standards
　Safety is taken into consideration to minimize the risk of injury in the event of an accidental collision with the robot.
LeatherScan is equipped as standard, so it can be operated without the need for a safety fence.
　Zic's nanoScan3 is standard equipment. By specifying the range, the robot can slow down or stop its operation if a person enters within the robot's moving range. It is also possible to limit the scanning range by installing a safety fence.

The FTS1000 is a purely Japanese-made tray sealing machine that can be manufactured, maintained, and supplied with parts in Japan.
The machine is designed to meet the needs of users' production sites, with a packaging line that is easy to use even for female operators, and tool-less cleaning in areas where cleaning is required.

Product Features
Tray sealing machine made in Japan
　Maintenance and parts can be provided in Japan.
A machine that is carefully designed in line with the user's production site.
　The cover of the feeding section is a horizontal sliding type, and the cover of the sealing section is a shutter type that opens and closes vertically.
Easy to clean and dirt-resistant
　The installation height of the thermal printer, which requires cleaning, is designed to be low. Stopper-equipped conveyor is employed, with a supply conveyor and each stopper to prevent contamination, and stable conveyance is possible even with frozen food, etc.